AURVTN029 - Set up and operate universal vehicle measuring systems
Assessor Resource
AURVTN029 Set up and operate universal vehicle measuring systems
Assessment tool
Version 1.0 Issue Date: May 2024
This unit describes the performance outcomes required to set up and use a universal measuring system to measure vehicle chassis misalignment at pre- and post-repair intervals. It involves preparing for the task, selecting and using specialist tools and equipment, setting measuring equipment, measuring vehicle upper and underbody in three dimensions, and completing workplace processes and documentation.
It applies to those working in the automotive body repair industry.
No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)
Evidence Required
List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements
Elements describe the essential outcomes.
Performance Criteria
Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.
1. Prepare to set up and operate universal measuring system
1.1 Job requirements are determined from workplace instructions
1.2 Set-up information is accessed and interpreted
1.3 Hazards associated with the work are identified and risks are managed
1.4 Measuring equipment is selected, set up, and calibrated and checked for serviceability
1.5 Work is planned to complete job requirements efficiently
2. Carry out measurement activities
2.1 Measuring system is secured and adjusted to vehicle according to original equipment manufacturer (OEM) or authorised agency’s recommended procedures and safety requirements
2.2 Vehicle is measured in three dimensions according to OEM or authorised agency’s requirements and workplace procedures, and without causing damage to vehicle system or components
2.3 Pre- and post-repair measurements are recorded according to workplace procedures
3. Complete measurement processes
3.1 Final checks are made to ensure measurements are accurate, meet workplace expectations, and comply with OEM or authorised agency’s specifications
3.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
3.3 Measuring equipment is checked and maintained according to manufacturer specifications, reported if faulty, and stored according to workplace procedures
3.4 Workplace documentation is processed according to workplace procedures
Before competency can be determined, individuals must demonstrate they can perform the following according to the standard defined in this unit’s elements, performance criteria, range of conditions and foundation skills:
set up and operate a universal measuring system on two occasions to take three-dimensional measurements (length, width and height) of upper and underbody on two vehicles with different types of chassis, including checking for the following types of damage:
diamond
twist
kick-up and kick-down.
Individuals must be able to demonstrate knowledge of:
work health and safety (WHS) and occupational health and safety (OHS) requirements relating to setting up and operating universal vehicle measuring systems, including procedures for:
following universal measuring equipment safety requirements
selecting and using personal protective equipment (PPE)
manual handling techniques
vehicle designs, including:
mono chassis
space frame
types of vehicle chassis misalignment damage, including:
diamond
twist
kick-up and kick-down
sag
mash and sway damage
original equipment manufacturer (OEM) or authorised agency’s specifications, including pre- and post-repair measurement intervals
procedures for final inspection of set-up and operation of a universal measuring system.
Assessors must satisfy NVR/AQTF assessor requirements.
Competency is to be assessed in the workplace or a simulated environment that accurately reflects performance in a real workplace setting.
Assessment must include direct observation of tasks.
Where assessment of competency includes third-party evidence, individuals must provide evidence that links them to the vehicles that they have measured and repaired using a universal measuring system, e.g. repair orders.
Assessors must verify performance evidence through questioning on skills and knowledge to ensure correct interpretation and application.
The following resources must be made available:
automotive workplace or simulated workplace
workplace instructions
OEM or authorised agency specifications and measurements
PPE required to set up and operate a universal vehicle measuring system
universal vehicle measuring system
universal vehicle measuring system operating instructions
two vehicles with different chassis types requiring pre- and post-repair measuring of the misalignment damage specified in the performance evidence
tools, equipment and materials appropriate for setting up and operating universal vehicle measuring systems.
Submission Requirements
List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here
Assessment task 1: [title] Due date:
(add new lines for each of the assessment tasks)
Assessment Tasks
Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.
Elements
Elements describe the essential outcomes.
Performance Criteria
Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.
1. Prepare to set up and operate universal measuring system
1.1 Job requirements are determined from workplace instructions
1.2 Set-up information is accessed and interpreted
1.3 Hazards associated with the work are identified and risks are managed
1.4 Measuring equipment is selected, set up, and calibrated and checked for serviceability
1.5 Work is planned to complete job requirements efficiently
2. Carry out measurement activities
2.1 Measuring system is secured and adjusted to vehicle according to original equipment manufacturer (OEM) or authorised agency’s recommended procedures and safety requirements
2.2 Vehicle is measured in three dimensions according to OEM or authorised agency’s requirements and workplace procedures, and without causing damage to vehicle system or components
2.3 Pre- and post-repair measurements are recorded according to workplace procedures
3. Complete measurement processes
3.1 Final checks are made to ensure measurements are accurate, meet workplace expectations, and comply with OEM or authorised agency’s specifications
3.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
3.3 Measuring equipment is checked and maintained according to manufacturer specifications, reported if faulty, and stored according to workplace procedures
3.4 Workplace documentation is processed according to workplace procedures
This section specifies work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Bold italicised wording, if used in the performance criteria, is detailed below.
Set-up information must include:
workplace procedures
measuring equipment information
OEM or authorised agency vehicle chassis specifications.
Measuring equipment must include:
universal measuring system
hand tools and equipment.
Set up must comply with:
recommended workplace procedures
specifications of OEM or authorised agency
vehicle specifications.
Safety requirements must include:
work health and safety (WHS) and occupational health and safety (OHS) requirements, including procedures for:
following universal measuring equipment safety requirements
selecting and using personal protective equipment (PPE)
manual handling techniques.
Three dimensions of measurement must include:
length
height
width.
Before competency can be determined, individuals must demonstrate they can perform the following according to the standard defined in this unit’s elements, performance criteria, range of conditions and foundation skills:
set up and operate a universal measuring system on two occasions to take three-dimensional measurements (length, width and height) of upper and underbody on two vehicles with different types of chassis, including checking for the following types of damage:
diamond
twist
kick-up and kick-down.
Individuals must be able to demonstrate knowledge of:
work health and safety (WHS) and occupational health and safety (OHS) requirements relating to setting up and operating universal vehicle measuring systems, including procedures for:
following universal measuring equipment safety requirements
selecting and using personal protective equipment (PPE)
manual handling techniques
vehicle designs, including:
mono chassis
space frame
types of vehicle chassis misalignment damage, including:
diamond
twist
kick-up and kick-down
sag
mash and sway damage
original equipment manufacturer (OEM) or authorised agency’s specifications, including pre- and post-repair measurement intervals
procedures for final inspection of set-up and operation of a universal measuring system.
Assessors must satisfy NVR/AQTF assessor requirements.
Competency is to be assessed in the workplace or a simulated environment that accurately reflects performance in a real workplace setting.
Assessment must include direct observation of tasks.
Where assessment of competency includes third-party evidence, individuals must provide evidence that links them to the vehicles that they have measured and repaired using a universal measuring system, e.g. repair orders.
Assessors must verify performance evidence through questioning on skills and knowledge to ensure correct interpretation and application.
The following resources must be made available:
automotive workplace or simulated workplace
workplace instructions
OEM or authorised agency specifications and measurements
PPE required to set up and operate a universal vehicle measuring system
universal vehicle measuring system
universal vehicle measuring system operating instructions
two vehicles with different chassis types requiring pre- and post-repair measuring of the misalignment damage specified in the performance evidence
tools, equipment and materials appropriate for setting up and operating universal vehicle measuring systems.
Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.
Observation Checklist
Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice
Yes
No
Comments/feedback
Job requirements are determined from workplace instructions
Set-up information is accessed and interpreted
Hazards associated with the work are identified and risks are managed
Measuring equipment is selected, set up, and calibrated and checked for serviceability
Work is planned to complete job requirements efficiently
Measuring system is secured and adjusted to vehicle according to original equipment manufacturer (OEM) or authorised agency’s recommended procedures and safety requirements
Vehicle is measured in three dimensions according to OEM or authorised agency’s requirements and workplace procedures, and without causing damage to vehicle system or components
Pre- and post-repair measurements are recorded according to workplace procedures
Final checks are made to ensure measurements are accurate, meet workplace expectations, and comply with OEM or authorised agency’s specifications
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
Measuring equipment is checked and maintained according to manufacturer specifications, reported if faulty, and stored according to workplace procedures
Workplace documentation is processed according to workplace procedures
Job requirements are determined from workplace instructions
Set-up information is accessed and interpreted
Hazards associated with the work are identified and risks are managed
Measuring equipment is selected, set up, and calibrated and checked for serviceability
Work is planned to complete job requirements efficiently
Measuring system is secured and adjusted to vehicle according to original equipment manufacturer (OEM) or authorised agency’s recommended procedures and safety requirements
Vehicle is measured in three dimensions according to OEM or authorised agency’s requirements and workplace procedures, and without causing damage to vehicle system or components
Pre- and post-repair measurements are recorded according to workplace procedures
Final checks are made to ensure measurements are accurate, meet workplace expectations, and comply with OEM or authorised agency’s specifications
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
Measuring equipment is checked and maintained according to manufacturer specifications, reported if faulty, and stored according to workplace procedures
Workplace documentation is processed according to workplace procedures
Forms
Assessment Cover Sheet
AURVTN029 - Set up and operate universal vehicle measuring systems
Assessment task 1: [title]
Student name:
Student ID:
I declare that the assessment tasks submitted for this unit are my own work.
Student signature:
Result: Competent Not yet competent
Feedback to student
Assessor name:
Signature:
Date:
Assessment Record Sheet
AURVTN029 - Set up and operate universal vehicle measuring systems
Student name:
Student ID:
Assessment task 1: [title] Result: Competent Not yet competent
(add lines for each task)
Feedback to student:
Overall assessment result: Competent Not yet competent